Torque pro ford pid list
- #Torque pro ford pid list how to
- #Torque pro ford pid list install
- #Torque pro ford pid list manual
- #Torque pro ford pid list android
- #Torque pro ford pid list mods
This would be approximately 0 to 1074.3 cfm assuming STP conditions. Ill go through the rest later today and post what else works.
Coolent Pid: 0167 Equation b-40 auto, that should give you the engine coolant temp sensor.
#Torque pro ford pid list install
The mode 1 PID for MAF (0x10) produces a value from 0 to 655.35 g/s. Ironically, I have an old install of Torque from my VW TDI a few years ago on a tablet. So 1 cfm 36.6/60 or 0.61 grams per second. Now with Apple Support! You will need a different OBD2 dongle because the Apple devices don't allow bluetooth connection to dongles like these. At STP, a cubic foot of air weighs 0.081 pounds or 36.6 grams.
#Torque pro ford pid list manual
Ford Focus Service Manual / Powertrain / General Information / Parameter Identification (PID) / Generic OBD PID List An X in the Freeze Frame column denotes both a mode 1 and mode 2 PID (real time and freeze frame).
#Torque pro ford pid list android
$21 BAFX Products Android Wireless Bluetooth OBD2 Scanner & Fault Code Reader Diagnostic Scan Tool for Cars & Trucks – for All OBD2 Protocols on All Consumer Vehicles 1996 & Newer Compatible APPs:Torque Lite/Pro (recommended), DashCommand, OBD Fusion, OBD Car Doctor, OBD Auto Doctor etc.
#Torque pro ford pid list how to
If you don't know what Torque is or how to connect to your Android device, you will need a Bluetooth OBD2 dongle and Torque Pro App. Long Name: Transmission Fluid Post-Converter Temperature Anyone have a clue These three are most important at the moment Injection Control. Check that the klavkarr diagnostic scanner will work with your car. You can read their feedback on this page. Bello with the XXX are the ones that wont respond. Several thousand OBD2-compatible vehicles have been tested by our customers with klavkarr. But I am getting a lot of PID that are inactive. But I have seen lots of differences in PID assignments across models, even occassionally on identical vehicles -just manufactured at a different assembly plant. These PIDs should work on almost all 2004 - 2008 F150 trucks. I also did scan when connected to the truck. For Torque Pro users - who might wish to monitor these OBDII signals /with my disclaimer. Long Name: Transmission Fluid Pan Temperature Just got the Torque Pro and and added the custom PID's for ford. Unbolded items can be changed or left alone. Press three dots uppper right, this is the menu. From home screen, press the gear in lower left.
#Torque pro ford pid list mods
2010 GT500 coupe, Kona Blue w/silver stripes & orange pins, ported VMP Gen 2, CJ dual 65mm TB, JLT 123 CAI, VMP dual BAP, 52lb inj's, VMP triple pass HE, BPS fuel rails, & misc suspension and appearance mods (blue & orange theme), Continental Extreme. I have not verified this on 4 cylinder models. My F350 PIDs are easily identified by name from the Ford list PIDs. Torque PID list and cross referenced it with. Just getting started but hopefully I can contribute some PID data as I work through the startup glitches - thanks in advance for any assistance.Here are the PIDs and other values you need to enter into Torque Pro on an Android device to monitor your transmission fluid temperatures on a 2016+ Tacoma.Ģ016+ Tacoma, V6, Automatic transmission. Whats New: Added link to PID editor from dashboard screen in display configuration when the display is linked to a user created PID J1939 support for large vehicles (Busses, Boats, Plant equipment, etc) Select the protocol from the vehicle profile settings to use it. I am using an OBDlink MX+ dongle which claims HSCAN/MSCAN support paired with a two channel CAN bus sniffer on pins 6/14 and 3/11 (via a splitter cable) and don't see any traffic when I have a ForScan dashboard set to a module on one of the other buses (for example, APIM to grab GPS lat/long data) so I am thinking I might be missing something. I understand that Ford might expose another CAN bus on pins 1 and 8/9 and was wondering if anyone has seen documentation to this effect and if there is something I should be looking at. I have been poking around the CAN bus and see that ForScan Lite shows me modules on HSCAN (pins 6 and 14), MSCAN (pins 3 and 11) but also modules on the HSCAN2, HSCAN3, HSCAN4, and FDCAN buses. (09-05-2019, 12:17 AM) Aleksey-MS Wrote: Torque Pro + PID files + Plugins + Initialization string Torque Pro - the best program for diagnosing cars using the ELM327 Bluetooth adapter + smartphones/tablets on Android. Hi all, with short days and long nights I usually pick a winter project to learn something new and this year it is extracting as much useful data as I can from my Mach-E.